Aquarium Driftwood

Aquarium Driftwood

Aquarium driftwood takes time, but you will save extraordinary amount of  money. Even small pieces of drift wood and cost well over $20. Also, the soak method (minus salt) will work for store bought driftwood. Store bought driftwood is cleaned and has not been soaked. This can lead to tannin's being leaked into your home aquarium and death to your fish.

Aquarium Driftwood Knowledge

Driftwood, which can be found anywhere. It doesn't necessarily have to come from the water. You could find it in the woods, as long as it is weathered down and looks unique. Also make sure the wood is not rotting.

BIG soaking container, I use a 15 gal rubber maid container.
 
Step one, clean off your wood! Make sure all debris and bark are removed from the wood (or it'll fall off in your tank!). Once complete, boil the water in the BIG pot and add aquarium salt. I use about a tablespoon per gallon. Boil the entire piece for about 2-4 hours depending on your size. If you can only fit half the wood in the pot then you will need to boil the other half.

 

Aquarium Salt, I use Doc Wellfish brand. This is used as a natural way of killing bacteria and parasites.


Step two once the boil is complete you can transfer your wood into the rubber maid container. Add water until the whole piece of wood is under water (you can also add salt if you want). If the wood does not sink place something on top of it until it does. It'll sink after a week or two.

You'll notice the water turn into tea-ish color. It is the result of the tannins that are released into the water. If you didn't soak the wood, the water in your tank would be this color. Tannins are natural and some fishes actually like it because it'll make them feel more at home. It'll also affect your PH, I'm not sure about GH or KH. You'll need to do water changes every other day to clean the water. This may take weeks or months.

Step 3 when the color of the soak water suffices, you will need to soak your wood for another week without any salt. This will make sure that the wood does not hold any salt that may leak into your tank.

Step 4 once soaking is complete wash the wood well and transfers the wood into your tank. Do not keep the wood out of water for a long time or it will float.

For more information and pictures about this project, please visit www.carolinafishtalk.com/ and check the DIY section.

Article written by krayzievanh@yahoo.com, member of CFT Community
Proof read by Brandan Njagu b.njagu@gmail.com

Aquarium Upkeep Basics

Aquarium Upkeep Basics

Today, aquariums have advanced to the point that the tanks are self-sufficient. Water conditions are important to check, since in each area of the world, water is different. In fact, some area waters are more contaminated than other areas. The types of fish factors into water, as well plants play a role too. Tetras is a type of fish, which naturally habitats in rainwater, or when in aquariums the fish enjoys soft waters. Therefore, when you test waters for these fish make sure that the waters are soft.

Cichlid is another species of fish that prefer harder water. The specimens came from the Rift Valleys of Africa, which contains dissolved salt. The salt was available from natural sources, such as lakes and rock lining.

How do I avoid hardening the water?

If you want hard waters, then do not add limestone. Limestone should be avoided, especially if you intend to use it as rocks or gravel.

How can I tell the condition of waters after testing pH?
After you test the waters, pH readings should give you a figure. If the number is below seven, then the water is acidy. If the figure is higher than seven are then the water is alkalinity or alkaline. The neutral pH figure is pH7. If the water conditions are below or higher than this figure then your water is too alkalinity and/or acidity. If you maintain a correct temperature and balance of water, your fish and plants will live long and healthy.

Tip: Red Nosed Tetra prefers freedom to swim and density of plants.

If you have test water keep in mind that tap water has pH7 or pH8 reading usually. If the gauge reads higher or else lower, it means that the water is too alkalinity or acidy: Keep in mind that discus from the symphysodon aequifasciata specimen enjoy acidy waters. If you have cichlids from Rift Valley, these fish prefer alkaline.

How do I test water?

You will need to purchase a test kit. You can purchase test kits online or preferably at your local pet store. Of course, you can purchase the kits online, but if you are not familiar with the types, it is best to purchase at a pet store. The test kits will provide you a read out of chemicals in the water as well, such as chlorine. There should not be chlorine in the waters; however, tap water may have such chemicals. Water conditioners are ideal. When you setup your tank and each time you refill the tank you should use water conditioners.

Tip: If you have a heater in the tank, keep the volume low.

Typically, it is not recommended that you locate your aquarium in a living room. Since most living rooms are too warm, the fish will feel agitated. However, if you have tropical fish as well as plants you will have fewer problems. Plants and fish from the tropical regions tend to adapt well to higher water or room temperature. Using a heater in the tank can help you preserve your fish, yet you want to keep the heater on low volume. Maintaining a volume of heat will also prolong the life of your heater.

If you are heating your aquarium, take the easy way out. Some heaters include heaterstats, which will help you regulate heat. Heaterstats are thermostatically controlled devices, which fix to the corners of an aquarium. You can use suction cups to mount the heater. The heater has a small lamp, which will click on each time the heater is activated.

Visit the Types Of Sharks website to learn about rainbow shark and dogfish shark.